* This adapter can be used to read the pin code of the transponder key automatically, and write the pin code into the computer transponder of the suited ECU. It can be used to match the vehicle without keys and  needn’t change any computer when matching.Be suitable for all the Toyota Series from 1997 to 2005. 

* It works with the cars from Asia, Euro and U.S.A.

* Be suitable for the transponder key’s match of Toyota, such as LEXUS (LS400 ES300 GS300 IS2000 IS300),Camry 2.0,2.4, JEEP-2007 3400 4500 4700, AVALON, PREVIA. 

* Equip English using manual. Offer technology support.

* From the date of purchase, we provide for a 18 months repair warranty with conditions.

* Use for the following cars:

1. ES300(1997-2003)
2. GS300(1997-2003)
3. GS400(1997-2000)
4. GX430(2001-2003)
5. IS300-IS200(2001-2003)
6. LS400(1997-2000)
7. LX470(1998-2002)
8. RX300(1999-2003)
9. SC300(1998-2001)
10. SC400(1998-2001)
11. 4Runner(1999-2003)
12. Avalon(1998-2003)
13. Cammry-4cly(1998-2005)
14. HighLander(2001-2003)
15. Lander Cruiser(1998-2003)
16. MR2(2000-2003)
17. RAV4(2000-2003)
18. Sequoia(2000-2003)
19. Sienna(1998-2003)
20. Solara(1999-2003)
21. Previa(1999-2003)

Operations of key programmer:

 I、Appearance introduction

 II、Operation of starting the device

Put DC15V power connector into the device’s plug. When hear a sound like “DI”, the device begins to check itself and starts to scan the screen. “P” will display on the screen after scanning. Just as the following picture show:

III、Operation of reading key data

1. When press the [Read] button, the screen will display “RE”, that means the device is in the condition of inducting and reading the data. Otherwise it will display “ER”(Error). You should to repeat the operation, until “RE” appears.

2. Put a key need to be matched close to the device, the device begins to induct and read the key’s data. When your hear “DI” for 3 times and “OK” appears on the screen, the read of key’s data has been finished. Otherwise the operation is failed. You should follow step1and step 2 to redo again.

IV、Operation of reading in the Data

1. Dissemble the memory chip from ECU, clean it and put it into the chip clamp. Then put the chip clamp on the programmer’s lock holder and lock it. As the right picture show.

2. This device is suitable for TOYOTA Series. Firstly according to your car’s type, then press the [MODE] button to choose suitable pattern. There are 4 kinds of pattern for you to choose, including “56”, “T1”, “T2”and “86”. If your car is TOYOTA CAMRY, you should choose pattern “56”, it will tell you the corresponding chip of your car is 93C56, you should dissemble it from the position of IC601 of the ECU; If the type of vehicle is TOYOTA (4700, AVALON, or LEXUS), you should choose pattern “T1” and dissemble chip 93C56 from the position of IC900 of the ECU; If the type of vehicle is TOYOTA (USA)\ (EUROPEAN) 4700 and LEXUS 400, you should choose pattern “T2”. But because these two kinds of vehicle have anti-theft computer and there’s no memory chip in the ECU, that you should only dissemble the chip 93C66 of anti-theft computer directly; As the same, if the type of the vehicle is new style PREVIA, you should choose pattern “86” and dissemble chip 93C86 from the position of IC900 of ECU. Patterns will be displayed on the screen like the following picture:

3. Press the [PROGRAM] button to make device read in the inducted key’s code into the ECU. During the data has been reading in, the screen would glitter and display “WR”. When the data has been read in the ECU, “OK” will appear on the screen and your will hear a sound “DI” once. Otherwise the operation is failed. Please to check the reasons! The possible reason is: chip has been put in the wrong position, chip hasn’t been clipped or choose unsuitable pattern.

4. After the writing of date, the chip should be put back into the ECU.

The matching of key has been finished. And the new key can be used to start the vehicle.

v、Copy Auto key:

1.TOYOTA key adapter can be used to copy 3 keys at the same time. You should need to repeat the step1 and step 2 of [Operation of reading key data].

2.Device supports on direct current 12V-15V. Please make sure the power off when the device hasn’t been used.

VI、Notice:

1.This function will cancel all the legit key code.

2.You should do the synchronous matching program during all the Auto keys (including new matching keys) and Engine Control Unit or Anti-theft Machine Control Unit.

3.If the user lost a legit key, you must make all the legit keys to be refinished the key matching program in safe. This operation can make the losing legit key invalidate.

Notice: This machine only provide for locksmiths. Please offer related business license, original ID card and need to sign the declaration with us.